![]() ![]() When you get to the end of the bottom row, connect your cable to signal 1 on the bottom row and jump to signal 1 on the top row. Note: if you have a larger sign that has multiple rows of sections. At the end you will have a signal 1 port available behind the antenna cable. Then continue your connect from sign 1 to signal 2. Repeat this step until all the signal cables are connected.įor double sided LED signs continue your connection by connecting to signal 1 at the end to the sign 2 on the other side immediately behind signal 1. ![]() ![]() Then connect the other end of the cable to signal 2 on the next section. Start by connecting the signal cable to the Signal 1 port on the main section. Your signal cable has two 9 pin connectors on both ends of the cable. How to connect your signal cables to extend the image on you led sign When installing the antenna, ensure the antenna is installed vertically with the cable coming from the bottom of the antenna. You should also see the antenna label on the cap on the back of the sign. If there are no lights, check to make sure you connected to the correct port. Once they are correctly connected you should immediately see the power lights on the side or front of the antenna depending on your configuration. In this case connect the cable to the WAN Port. If you opted for the 4G LTE antenna, your antenna may have 2 ports. Connect the cover and reinstall the cover. To connect the cable to the antenna, remove the cover at the bottom to reveal the ethernet port. (note the included POE injector will not be used at this stage, so do not connect to the sign). And connect the other end directly into your antenna. ![]() Connect the Antenna cable to the signal 2 port on the main section. Your Antenna cable has a 9 pin connector on one end and an ethernet/RJ45 connector on the other end. The antenna connects to the signal 2 port on the outside edge of the sign below the sensor. How to connect your LED Sign’s network antenna. And follow proper safety procedures to prevent electrical shock. Note the color code for your wires:īe sure to secure the power connector to them before turning the power on. The main cabinet is usually on the left side of the sign (when looking at the front of the sign).Īfter plugging in your power cables, you will need to terminate the wires to your junction/breaker box (not included). Depending on your configuration, there will be a 9-pin connector or 4 pin connect in the power 2 port on the main cabinet. The power 2 port on the main cabinet has been converted to your brightness sensor port. Plug the power cable to Power 1 on the main cabinet, and Power 1 or Power 2 on the remaining sections. You will connect one power cable to each section. The second end of the cable is either unfinished or has terminal connectors preinstalled.Īll Sections, except for the main section, have two power ports, with the labels Power 1 and Power 2. Įnclosing the program settings / size / custom borders īackground, color, size and position can be freely adjusted.Īdvanced settings: Temperature / humidity / light sensors / wireless RF module / remote control.īrightness settings: enclosing three modes of brightness.Your power cables are the 13/14 AWG cables with a preinstalled 3 Pin Weatherproof connector on one end. Text, image, time, number, temperature (module should be connected.) and others. Text content: text, images, time, temperature, graphics, animations.ĭisplay Modes: switch buttons or remote control. Programs: More than 200 programs are available that can change with the buttons or remotely. Seven colors: full color gamut reproduces colors red, green, blue, yellow, purple, blue and white. Operating environment: -40 degrees - 75 degreesĭimensions of installation: 92.0 (H) * 100.0 (W) (mm)įLSH capacity: 2MB (can be extended to 8M Byte)Ĭommunication ports: U-Disk / RS232 serial port / network portĬolor: Dual color maintained all the red, green and yellow. Types of communication: U-Disk / RS232 serial port / network port Type of control card: a color / double color / seven-colorĬontrol range: 512 * 1024 * 1 for a single color 512 * 512, 128 * 64 * 20 in two colors 256 * 6 * 128 for seven colors Scope of application:This product is applied Signage, shops, vehicles, outdoor advertising and more.Īdvantages: wireless transmission of U-Disk & RS232 serial port and a network port, cost effective, simple software interface, easy to use, rich and subtle effects on the display above all, more than 98% of single / double color screens are supported.Īpplication Software: fourth-generation operating software HD2014 screen Gypsum plasterboard and Gypsum fiberboard. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |